This fixes a serious bug on NixOS with swraid where mdadm arrays weren't
properly stopped on shutdown. Rather than fixing the unit by adding
`Before=final.target` we completely move to upstream units, which uses
systemd shutdown hooks instead. This also drives down maintenance costs
for us.
Introduces a trim timer similar to the fstrim service.
According to zpool(8) for consumer hardware periodic manual TRIM
is preferred over automatic TRIM that ZFS implements.
The period of one week is based on recommendations of fstrim.
This is a refactor of how resolvconf is managed on NixOS. We split it
into a separate service which is enabled internally depending on whether
we want /etc/resolv.conf to be managed by it. Various services now take
advantage of those configuration options.
We also now use systemd instead of activation scripts to update
resolv.conf.
NetworkManager now uses the right option for rc-manager DNS
automatically, so the configuration option shouldn't be exposed.
Same as zfsUnstable for the moment.
We still keep the zfsUnstable expression as we likely
need it in the near future again.
Also remove spl since it is no longer needed.
With systemd v242 using the `Gateway` attribute of the `[Network]`
section will lead to "onlink" routes on all the device that are matched
by the default configuration (typically all devices) causing multiple
default routes (even on localhost).
We can only avoid that - while keeping our default route option - when
we mark the route as explicitly not on link. Only gateways that are
within a subnet of one of the assigned interface addresses will be
installed into the routing table.
Assert that autoResize is only used when fsType is explicitly set to a
supported filesystem: if it's set to "auto", the default, the required
resizing tools won't be copied into the initrd even if the actual
filesystem is supported.
27982b408e introduced a bug when
refactoring the encrypted-devices module, causing some encrypted
filesystem options to not be recognized anymore.
See e.g. https://hydra.nixos.org/build/88145490
This adds a NixOS option for setting the CPU max and min frequencies
with `cpufreq`. The two options that have been added are:
- `powerManagement.cpufreq.max`
- `powerManagement.cpufreq.min`
It also adds an alias to the `powerManagement.cpuFreqGovernor` option as
`powerManagement.cpufreq.governor`. This updates the installer to use
the new option name. It also updates the manual with a note about
the new name.
When a bridge interface was reconfigured, running containers using
this bridge lost connectivity: restarting network-addresses-brN.service
triggered a restart of network-setup.service via a "partOf" relationship
introduced in 07e0c0e0a2.
This in turn restarted brN-netdev.service.
The bridge was thus destroyed and recreated with the same name but a new
interface id, causing attached veth interfaces to lose their connection.
This change removes the "partOf" relationship between
network-setup.service and network-addresses-brN.service for all bridges.
1. Simplify the command by reading directly from /etc/machine-id which
is already a random, lower-case hex string
2. Previously, the command output could be too short because of missing
leading digits. This is now fixed.
when the parent interface of a vlan interface is not up (yet), ip link cannot bring the vlan interface up
the vlan interface will be automatically brought up when the parent interface is up later
fix NixOS/nixpkgs#28620
With a config like
{
networking.interfaces."lo".ip4 = [
{ address = "10.8.8.8"; prefixLength = 32; }
];
}
a nixos-rebuild switch would take a long time, and you'd see:
$ systemctl list-jobs
JOB UNIT TYPE STATE
734400 network-interfaces.target start waiting
734450 sys-subsystem-net-devices-lo.device start running
734449 network-link-lo.service start waiting
and:
systemd[1]: sys-subsystem-net-devices-lo.device: Job sys-subsystem-net-devices-lo.device/star>
systemd[1]: sys-subsystem-net-devices-lo.device: Job sys-subsystem-net-devices-lo.device/star>
systemd[1]: Timed out waiting for device sys-subsystem-net-devices-lo.device.
This removes the device dependency for `lo` and fixes this bug.
Closes #7227
fixes #41838
At the moment it works fine for "file://" keys, but does not work for
dataPools with "prompt" keys, because the passphrase cannot be entered
(yet).
Resolved the following conflicts (by carefully applying patches from the both
branches since the fork point):
pkgs/development/libraries/epoxy/default.nix
pkgs/development/libraries/gtk+/3.x.nix
pkgs/development/python-modules/asgiref/default.nix
pkgs/development/python-modules/daphne/default.nix
pkgs/os-specific/linux/systemd/default.nix
Users were confused that the error message said config.networking.hostId, and indeed that did nothing to fix their problem.
Update the error message to specify the option they should actually set.
Reverse the PartOf dependency between network-setup and network-addresses-*
This was joint work of: @nh2, @domenkozar, @fpletz, @aszlig and @basvandijk
at the NixCon 2017 hackathon.
