Following legacy packing conventions, `isArm` was defined just for
32-bit ARM instruction set. This is confusing to non packagers though,
because Aarch64 is an ARM instruction set.
The official ARM overview for ARMv8[1] is surprisingly not confusing,
given the overall state of affairs for ARM naming conventions, and
offers us a solution. It divides the nomenclature into three levels:
```
ISA: ARMv8 {-A, -R, -M}
/ \
Mode: Aarch32 Aarch64
| / \
Encoding: A64 A32 T32
```
At the top is the overall v8 instruction set archicture. Second are the
two modes, defined by bitwidth but differing in other semantics too, and
buttom are the encodings, (hopefully?) isomorphic if they encode the
same mode.
The 32 bit encodings are mostly backwards compatible with previous
non-Thumb and Thumb encodings, and if so we can pun the mode names to
instead mean "sets of compatable or isomorphic encodings", and then
voilà we have nice names for 32-bit and 64-bit arm instruction sets
which do not use the word ARM so as to not confused either laymen or
experienced ARM packages.
[1]: https://developer.arm.com/products/architecture/a-profile
The first problem that was introduced in a276d5160c
was a linking error:
ld: cannot find -licui18n
ld: cannot find -licuuc
ld: cannot find -licudata
So I added icu to the buildInputs.
The second problem was that the interpreter wasn't patched in
share/filters, apparently this is only needed when building with
autotools:
make[3]: Entering directory '/build/inkscape-0.92.3/share/filters'
./i18n.py ./filters.svg > ./filters.svg.h
./i18n.py: /usr/bin/env: bad interpreter: No such file or directory
A similar error also occurs for share/palettes, share/patterns,
share/symbols and share/templates, so I added patching the interpreter
there as well.
Switching to autotools in Inkscape is a very bad idea, because upstream
currently still has their own autotools files in the 0.92.x tree but
master already has them removed, see this commit:
e471a664f9
However for the sake of trying to not break Inkscape on Darwin again,
I tried to keep the fixes minimal and not went back to CMake.
I did however mark the stuff that's unneeded for CMake, so that we can
avoid forgetting to remove that crap once we get back to CMake.
Signed-off-by: aszlig <aszlig@nix.build>
Cc: @matthewbauer
Otherwise the build fails with the perplexing error
make: *** No rule to make target 'cmd-list.made', needed by 'doc.dep'. Stop.
make: Leaving directory '/tmp/nix-build-git-2.16.3.drv-0/git-2.16.3/Documentation'
on NixOS (but not on Debian, where it succeeds, presumably since it picks up the
system perl).
Semi-automatic update generated by https://github.com/ryantm/nixpkgs-update tools.
This update was made based on information from https://repology.org/metapackage/latte-dock/versions.
These checks were done:
- built on NixOS
- ran ‘/nix/store/6nvkkskm7j4ngqfy722ajp289gqhg1a9-latte-dock-0.7.5/bin/latte-dock -h’ got 0 exit code
- ran ‘/nix/store/6nvkkskm7j4ngqfy722ajp289gqhg1a9-latte-dock-0.7.5/bin/latte-dock --help’ got 0 exit code
- found 0.7.5 with grep in /nix/store/6nvkkskm7j4ngqfy722ajp289gqhg1a9-latte-dock-0.7.5
- directory tree listing: https://gist.github.com/8f58b4f85d4c80752b6d66e912ce92c0
Semi-automatic update generated by https://github.com/ryantm/nixpkgs-update tools.
This update was made based on information from https://repology.org/metapackage/pcmanfm/versions.
These checks were done:
- built on NixOS
- ran ‘/nix/store/z37gyw9vskaby2caizkzghjd7ikafv64-pcmanfm-1.3.0/bin/pcmanfm -h’ got 0 exit code
- ran ‘/nix/store/z37gyw9vskaby2caizkzghjd7ikafv64-pcmanfm-1.3.0/bin/pcmanfm --help’ got 0 exit code
- ran ‘/nix/store/z37gyw9vskaby2caizkzghjd7ikafv64-pcmanfm-1.3.0/bin/.pcmanfm-wrapped -h’ got 0 exit code
- ran ‘/nix/store/z37gyw9vskaby2caizkzghjd7ikafv64-pcmanfm-1.3.0/bin/.pcmanfm-wrapped --help’ got 0 exit code
- found 1.3.0 with grep in /nix/store/z37gyw9vskaby2caizkzghjd7ikafv64-pcmanfm-1.3.0
- directory tree listing: https://gist.github.com/f15deaa66af5124a632abbca797f7240
