Applies OpenWRT's noscan patch to hostapd and the relevant option to
the hostapd module.
This noscan patch adds a new `noscan` option allowing us to create
some overlapping BSSs in HT40+/- mode.
Note: this option is disabled by default, we leave this up to the end
user whether it should be enabled or not.
Not being able to create those overlapping BSSs is basically
preventing us to use 802.11n in any urban area where chances to
overlap with another SSID are extremely high.
The patch we are using is a courtesy of the openwrt team and is
applied to the defaul hostapd package in both OpenWRT and Archlinux.
Using "builtins.currentSystem" doesn't work in pure evaluation mode,
and even when it's explicitly set (which it always is, in
nixos/lib/eval-config.nix), it breaks manual generation because the
manual tries to render the default value.
The change to "NixOS Test Cluster" in #59179 broke startup of existing clusters
that used the previously-default cluster name "Test Cluster":
ERROR 23:00:47 Fatal exception during initialization
org.apache.cassandra.exceptions.ConfigurationException: Saved cluster name Test Cluster != configured name NixOS Test Cluster
Fixes#63388.
This will keep configuration configuring the size of the /boot partition
still build, while showing the deprecation warning.
In 99.9% of cases I assume ignoring the configuration is better, as the
sd-image builder already is pretty opinionated in that matter.
The slack, seemingly, accounted for more than the minimum required for
slack plus the two partitions.
This change makes the gap a somewhat abstracted amount, but is not
configurable within the derivation.
The current FAT32 partition is kept as it is required for the Raspberry
Pi family of hardware. It is where the firmware is kept.
The partition is kept bootable, and the boot files kept in there until
the following commits, to keep all commits of this series individually
bootable.
Up until now, the output has been the same for swap devices and swap
files:
{ device = "/var/swapfile"; }
Whereas for swap *files* it's easier to manage them declaratively in
configuration.nix:
{ device = "/var/swapfile"; size = 8192; }
(NixOS will create the swapfile, and later resize it, if the size
attribute is changed.)
With the assumption that swap files are specified in configuration.nix,
it's silly to output them to hardware-configuration.nix.
This will reduce the confusion at boot, where the only thing visible is
the last message from u-boot; where it looks like the board is
hung, while in reality it's likely resizing partitions.
This will reduce the confusion at boot, where the only thing visible is
the last message from u-boot; where it looks like the Raspberry Pi is
hung, while in reality it's likely resizing partitions.
Fixes the broken metrics evaluation which was caused by a `trace`
warning in stdout which confused `jq` in `pkgs/top-level/metrics.nix`.
Also made the `bind-device` feature optional as suggested after the
merge.
Manual build broken by 79f7f89442, which
is part of pull request #59179 (Fix Cassandra, improve config and
tests).
The issue was just a small error because of an unbalanced <literal/>
tag, so only a "/" was missing :-)
Signed-off-by: aszlig <aszlig@nix.build>
Cc: @aanderse
The the extraConfig variable is added below the domain variable in the
ddclient config file. The domain variable should always be last.
(cherry picked from commit ba0ba6dc79)
If the `seedAddresses` is not set, don't force `SimpleSeedProvider` to
be in `seed_provider`. This could cause problems in a multi-datacenter
deployment when a different seed provider is preferred.
Below that it works but only when supplying a custom password file with
restricted permissions (i.e. outside the nix-store). We can't do that
using an absolute path in the tests.
If you're on a multi user system you don't want to have the password in
the nix-store. With the new jmxRolesFile option you can specify your own
protected file instead.
Seems like you can't have a node as its own seed when it's listening on
an interface instead of an IP. At least the way it was done in the
test doesn't work and I can't figure out any other way than to just
listen on the IP address instead.
Add "bcache" to boot.initrd.availableKernelModules if a bcache device is
detected.
This fixes a problem I've had one too many times: I install NixOS and
forget to add "bcache", resulting in an unbootable machine (until fixed
with Live CD). Now NixOS will do it for me.
It is referenced in various places, but does not work out of the box:
$ nixos-help
/run/current-system/sw/bin/nixos-help: unable to start a web browser; please set $BROWSER
In the user-hidden fallbacks to xdg-open(1) and w3m(1), `nixos-help`
expects tools to be deliberately installed by users.
For default installations and new users in general, this is unlikely to
be the case. Conversely, chances to use `nixos-help` are even higher
in such cases.
Use w3m-nographics by default to ensure documentation is always
available. The documentation browser on ttyS8 already does so, but is
not accessible in every installation, e.g. VMs with only ttyS0 and SSH
available.
This obsoletes including it in the base profile's systemPackages,
so remove the @TODO as done.
Previously each oneshot peer service only ran once and was not
restarted together with the interface unit. Because of this,
defined peers were missing after restarting their corresponding
interface unit.
Co-Authored-By: Franz Pletz <fpletz@fnordicwalking.de>
This enhances #61423, which removed the gating of desktop-managers from
being linked to the xserver's state.
This, though, brought in xterm into all systems, even those without X
servers.
This change sets the *default* of the xterm desktop-manager to the state
of the xserver, keeping it enabled by default as a sane fallback.
The xterm desktop-manager can still be enabled or disabled as needed,
without it being affected by xserver's state.
This is needed for tcrypt and the benchmark subcommand. If enabled,
it is also used to unlock LUKS2 volumes and therefore the kernel modules
providing this feature need to be available in our initrd.
Fixes#42163. #54019.
This is a simple exporter which exports the information
provided by `wg show all dump` to prometheus.
Co-authored-by: Franz Pletz <fpletz@fnordicwalking.de>
This can lead to unnecessary failures if the kernel module is already
loaded:
Jun 06 12:38:50 chef bglisn9bz0y5403vdw9hny0ij43r41jk-unit-script-wireguard-wg0-start[13261]: modprobe: FATAL: Module wireguard not found in directory /run/booted-system/kernel-modules/lib/modules/4.19.36
Same as zfsUnstable for the moment.
We still keep the zfsUnstable expression as we likely
need it in the near future again.
Also remove spl since it is no longer needed.
See https://github.com/NixOS/nixpkgs/issues/15747. Previously this module was called `<unknown-file>`
in error messages, now it is called a bit more close to real:
```
module at /home/danbst/dev/nixpkgs/nixos/modules/virtualisation/containers.nix:470
```
Types are now specified for all options.
The fixed uid and gid for the avahi user have been removed
and the user avahi is now in the group avahi.
The the generic opening of the firewall for UDP port 5353 is
now optional, but still defaults to true.
The option `extraServiceFiles` was added to specify avahi
service definitions, which are then placed in `/etc/avahi/services`.
The geoclue module now lets us set application config. This should make
it more robust in desktop environments that don't define a geoclue
agent.
Fixes#45994.
The geoclue module now lets us set application config. This should make
it more robust in environments that don't provide a geoclue agent.
Fixes#44725.
We set stateVersion to `mkDefault 18.03` in
`nixos/modules/testing/test-instrumentation.nix` and in
`modules/installer/cd-dvd/installation-cd-base.nix`.
Accessing the stateVersion in the module system from within the tests
results in the following error:
> The unique option `system.stateVersion' is defined multiple times, in
> `nixpkgs/nixos/modules/installer/cd-dvd/installation-cd-base.nix' and
> `nixpkgs/nixos/modules/testing/test-instrumentation.nix'.
There are other tests that use it as well. Namely the radicale test also
verifies behaviour between state versions is as expected. It switches a
package default value. Others switched on the state directory default.
It seems like having the timesyncd switch as part of every rendered
activationScript might cause this weird error.
Removing this line seems like a reasonable thing to do since we actually
set the default to the very same value in the module system. This line
should have been no-op besides the issue that we've two statements
setting it in this very specific case.
The autoLuks module is not really compatible with the updated systemd
version anymore. We started dropping NixOS specific patches that caused
unwanted side effects that we had to work around otherwise.
This change points users towards the relevant PR and spits out a bit of
information on how to deal with the situation.
Somewhen between systemd v239 and v242 upstream decided to no longer run
a few system services with `DyanmicUser=1` but failed to provide a
migration path for all the state those services left behind.
For the case of systemd-timesync the state has to be moved from
/var/lib/private/systemd/timesync to /var/lib/systemd/timesync if
/var/lib/systemd/timesync is currently a symlink.
We only do this if the stateVersion is still below 19.09 to avoid
starting to have an ever growing activation script for (then) ancient
systemd migrations that are no longer required.
See https://github.com/systemd/systemd/issues/12131 for details about
the missing migration path and related discussion.
